Holybro GPS M10 IST8310 10 Pin
Holybro GPS M10 IST8310 10 Pin - Image 2
Holybro GPS M10 IST8310 10 Pin - Image 3

Holybro GPS M10 IST8310 10 Pin

Rp0,00

Available on backorder

Categories: , Brand:

The M10 GPS uses multi-constellation GNSS powered by the u-blox M10 series, a concurrent GNSS receiver that can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture, all four major GNSS constellations, GPS, Galileo, GLONASS, and BeiDou, can be received concurrently.

It also comes with the IST8310 or IST8308 compass, tricolored LED indicator, buzzer, and a safety switch. There are 3 different connector options for different purposes. This module ships with a baud rate of 115200 5Hz.

The high-gain 25 x 25 mm patch antenna provides excellent performance, and the omnidirectional antenna radiation pattern increases flexibility for device installation. It features active circuitry for the ceramic patch antenna and a rechargeable backup battery for warm starts.

Description

Feature

  • Ublox M9N GNSS Receiver
  • Accurate Positioning
  • Fast Navigation Update Rate
  • IST8310 or IST8308 Compass
  • High-gain 25*25*4mm antenna
  • Internal Buzzer, Safety switch
  • Ultra Bright UI RGB LED

Note

  • IST8308 is supported by PX4 V1.16.0+ on Pixhawk 6C and 1.14.3+ on Pixhawk 6X
  • The Status LED driver has changed. This LED is supported in PX4 1.14, ArduPilot 4.4.0 & later. (More info)

Specifications

Holybro M10 GPS Holybro M9N GPS
GNSS Receiver Ublox M10 Ublox M9N
Number of Concurrent GNSS Up to 4 GNSS Up to 4 GNSS
BeiDou BeiDou
Galileo Galileo
GLONASS GLONASS
GPS GPS
QZSS QZSS
Frequency Band GPS L1 GPS L1
Galileo E1 Galileo E1
GLONASS L1 GLONASS L1
BeiDou B1 BeiDou B1
SBAS L1 SBAS L1
QZSS L1 QZSS L1
Compass IST8310 or IST8308 IST8310 or IST8308
Output Protocol UBX (U-blox) UBX (U-blox)
NMEA NMEA
Accuracy 2.0m CEP 1.5m CEP
Nav. Update Rate Up to 25 Hz (single GNSS), Up to 25 Hz (4 concurrent GNSS)
Up to 10 Hz (4 concurrent GNSS)
GNSS Augmentation System EGNOS, GAGAN, MSAS, and WAAS EGNOS, GAGAN, MSAS, and WAAS
QZSS: L1S QZSS: L1S
Default Baud Rate 115200 115200
Input Voltage 4.7-5.2V 4.7-5.2V
Connector Type
JST-GH-10pin
JST-GH-6pin
Molex 1.25mm 6pin & 4pin & 3pin (not available for V2)
Antenna 25 x 25 x 4 mm ceramic patch antenna
Antenna Gain 1.5dbi
Antenna LNA Gain 22dB
Power consumption Less than 200mA @ 5V Less than 200mA @ 5V
Operating Temperature -40~80°C -40~80°C
Version
V1  V2
V1  V2
Dimension
φ50 x14.4 mm  φ51 x18.5 mm
 φ50 x14.4 mm φ51 x18.5 mm
Weight
32g  36.8g
 32g 36.8g
IP Rating
 NA IP67
 NA IP67
Cable Length 27cm (42cm cable purchase separately) 27cm (42cm cable purchase separately)
Other (V1) Tri-color LED Tri-color LED
Onboard Buzzer Onboard Buzzer
Safety Switch Safety Switch
LNA MAX2659ELT+ RF Amplifier LNA MAX2659ELT+ RF Amplifier
Rechargeable Farah capacitance Rechargeable Farah capacitance
Low-noise 3.3V regulator Low-noise 3.3V regulator

Note

  • The Status LED driver has changed. This LED is supported in PX4 1.14, ArduPilot 4.4.0 & later. (More info)
  • Ardupilot User: If unable to perform normal compass calibration “compass dance” for any reason, set parameter COMPASS_ORIENT=6 (Yaw270) for proper compass orientation.

PIN MAP

Reviews

There are no reviews yet.

Be the first to review “Holybro GPS M10 IST8310 10 Pin”

Your email address will not be published. Required fields are marked *

Related products